Simple Tail Light Wiring Repair Makes My Day


After dealing with mysterious engine trouble codes and then just a week later replacing the driver squib on our Dodge Ram, I nearly screamed when Rene came home at dusk one evening and immediately got out to run around the ruck and check all the lights. (I know better to laugh instead.) We easily noticed the rear left blinker was out. I didn’t get really frustrated, however, until I discovered the issue was not as simple as a burned out bulb.

tail light repaur
Hint: It wasn’t the bulb.

Thankfully, this was another one of those quick and easy repairs, thanks to having the right tool for the right job, and taking some basic troubleshooting steps.

How to Diagnose and Repair Tail Light Wiring

Do yourself a favor, and save yourself time and money, by learning to do the simple vehicle maintenance and repairs yourself. This is one if the simplest – even though it wasn’t as simple as changing a bulb. The sun was setting as I quickly removed the tail light lens, and popped in the spare bulb I always keep on hand. Dang, it wasn’t the bulb, and we were hitching up to leave town the next morning. What now?

What does a fast turn signal mean?

If your truck is anything like our Dodge Ram, a rapidly clicking turn signal indicates a “bad bulb or wiring” – at this point it was that “or wiring” part that bothered me. I knew the bulb was good, so the problem had to be with the connector, or somewhere in that wiring. Thinking fast, I removed the opposite tail light assembly and connected it to the left side connector I had removed. The left turn signal worked fine when connected to the right tail light. Problem solved! Almost.

How to Replace Tail Light Circuit Board

I was very grateful the tail light wiring issue was not somewhere in the truck. I determined the circuit board was bad. What were the chances the Auto Zone in Kerrville, Texas would have the part, and still be open? As it turns out, my chances were pretty good for both. We were in Truck Country after all. To my surprise, they had two Dodge Ram tail light circuit boards in stock and they were open late. In a rush to get  there, I quickly reassembled my tail lights. Perhaps a bit too quickly.

Tail light connector
Tail light connector, with all parts where they belong.

TIP: Make sure the wiring harness connector doesn’t come apart in the circuit board. When attempting to reconnect the left tail light circuit board, the connector would not fit. What the? I had just removed the other board!

S.T.O.P: Stop. Take a breath. Observe. Proceed. Instead of trying to force the connector in place, I looked closely and found that the blue bushing from inside the right side connector was stuck inside the left side circuit board. After prying that out and reattaching it inside the wiring harness, I was able to reconnect the bad circuit board and go pick up my new one, just in time.

multi-bit scredriver
The right tools for the right job

Must-Have Tools for Tail Light Repair

Sure, it’s smart to keep some spare tail light bulbs in your toolbox. But they won’t do any good if you can’t remove the lens assembly, or detach the circuit board. I find a ratcheting multi-bit screwdriver makes quick work of jobs like this. And, an assorted Torx bit set is vital for those simple repairs you think you can tackle quickly, only to discover that’s not a Phillips screw holding your tail light in place.

torx screw bits
Torx and Phillips Required

I keep a multi-driver screwdriver ratchet readily accessible in the top of my truck toolbox just for days like this. Of course, I picked up a couple extra bulbs while I was at Auto Zone, and finished my repair in the parking lot to confirm that the bad circuit board was the cause of the malfunctioning turn signal warning. With everything working, I drove back home in the dark with a bright smile on my face.

5 thoughts on “Simple Tail Light Wiring Repair Makes My Day”

  1. Wooden household furniture possesses something incredibly
    organic about it. There is this feeling of comfort, of nature and
    of style that could be be located in hardwood furniture.

    Hardwood is birthed coming from the earth. It feeds the
    fire, disintegrates in to drafts and ashes away. It is really
    near to the human presence in the world. Might
    be actually that is actually why it resonates a great deal along with us.
    Might be that is actually why you still get that warm feeling when you contact an abundant mahogany desk.

    Reply
  2. Thanks this was helpful; however I think I have a bad socket . Checked the other side and all the tickets the bulbs go in look the same. On the side that I’m having issues the one socket does not look like the other two. Hoping to replace this and my problem solved.

    Reply
  3. That’s funny, we just had the same problem with our truck. We ruled out the bulb being an issue and were about to investigate more when it resolved on its own. It happened just after we washed the truck, and we think some water leaked into the fixture area and then dried out. Nonetheless, I’m going to keep this bookmarked in case it happens again.

    Reply

Leave a Reply to Jim Cancel reply